用户名: 密码:  泵阀行业营销型网站建设
当前位置:网站首页 -> 水泵系列 >> 其他泵

进口单级双吸流程泵

英国GRIMM格林进口单级双吸流程泵 UK GRIMM Imported single stage double suction flow pump


英国GRIMM格林进口单级双吸流程泵概述: 
    
进口单级双吸流程泵系单级双吸两端支承式离心流程泵,是英国格林公司参照API610第10版设计的单级双吸流程泵,为径向部分双支撑高温重载设计,安装方式为中心支撑,泵体为双蜗室;双吸式叶轮,汽蚀余量小,轴向平衡好;进出口均朝上,安装检修方便;密封及冲洗系统按API682规范设计,可安装API682规范推荐的所有密封及冲洗方案。

         该系列泵是为满足输送有大颗粒及较为苛刻和重工位的需要而特殊设计,用于石油精制、石油化工和化学工业及其它地方输送石油及其产品、它完全符合美国石油学会AP1610规范。

         进口单级双吸流程泵具有可靠性高、使用寿命长、通用化程度高等特点,尤其是效率高更为突出。

英国GRIMM格林进口单级双吸流程泵结构特点:

         进口单级双吸流程泵是单级双吸两端支承式离心流程泵,泵壳径向部分。特别适用于输送高温高压以及易燃易爆或有毒的液体,其安装方式为水平中心线支承,以把热胀冷缩产生的变形及位移降低到最低限度。泵体设计成双涡室,以平衡泵的径向力。
         泵靠有压液体流动可以自行排气,但泵体蜗壳上部和下部均留有脐子,当用户需要排气和放液时,可以开 ZG3/4"螺孔。在工作现场用丝堵拧上。
         泵的吸入口和排出口法兰均为垂直向上,与泵体铸成一体,其法兰尺寸和压力等级均等效采用美国全国标准学会(ANSI)标准等级。根据使用温度和材料类别不同,法兰最高使用压力可达5MPa(约50kgf/cm2)左右。
         为了可靠,流程泵均使用铸钢壳体,其静水压试验为7MPa(约70kgf/cm2)。
         轴封腔(填料封)和泵盖是铸成一体的,它可以装填料密封及平衡型、波纹管或串联型的机械密封,腔外面铸有可供选者的水冷腔夹套,水冷夹套的配备必须是特别提出要求或者是输送介质为水质为水的温度超过66℃以及碳氢化合物温度超过150℃时用。当输送介质需要保温时,在其夹套内还可以通入低压蒸汽或其他保温介质。其静水压试验1MPa(约10kgf/cm2)冷却水进口接头ZG1/2";在泵盖下方,出口接头ZG1/2";在泵盖上方。蒸汽进口接头 ZG1/2";在盖上方,出口接头 ZG1/2";在泵盖下方。
         叶轮为整体铸造件,且随转子一起做动平衡,它与轴是用键传动,转子是两端支承。壳体密封环或叶轮密封环均为可更换的标准件,两者良好的匹配由材料及其不同硬度来保证。叶轮两端的密封环有意设计成大小不同的尺寸即靠止推轴承一侧的密封环稍小于另一侧,使泵造成轻微的轴向力,让轴永远处于受拉状态工作,避免转子的左右串动。
         泵两端是同样大小的轴承体,材料为铸钢和铸铁两种,用螺钉紧固在托架(瓦架)上,并用配合止口定位,靠联轴器端装一套径向轴承,另一端装两套背对背安装的推力球轴承,轴承采用甩油环润滑,油量适中,每个轴承体外铸有散热片,可供空气冷却(T≤120℃),还可选用风扇冷却(T=120-260℃)和水冷却(T≥260℃),其中风扇冷却尤为适用于缺水或水质差的地区。
         当泵轴承使用风扇冷却时,风扇将取代防尘盘的位置,这也是此种泵的独特之处。当泵轴承使用水冷却时,球轴承外面铸有水冷夹套。
         轴承体同时装有透明塑料圆形油标和油杯,以和控制油位,轴承体两端装有铜质防尘盘,伸向轴承压盖的内孔,既可以防止灰尘或水份进入,又可以防止油泄漏。当轴承万一破裂时,它还能起支承作用。
         为了检修不必坼卸吸入或吐出管路就很容易的坼出叶轮、轴承、轴封等。 单级双吸流程泵采用挠性膜片式加长联轴器部件,且与泵轴为锥型配合,坼装非常方便。
         泵的转向:从原动机往泵看为逆时针方向旋转。

英国GRIMM格林进口单级双吸流程泵技术参数: 
流              量:95-1740m3/h
扬              程:38-280m
口              径:进口直径:150-400mm
                         出口直径:100-300mm
转              速:1480-2970r/min
功              率:75-710kw
使  用   温  度:-45~+450℃(特殊需要可达到-196℃)
最大工作压力:5.0MPa

英国GRIMM格林进口单级双吸流程泵主要用途: 
          用于石油精制、石油化工和化学工业及其它地方输送石油。

UK GRIMM Imported single stage double suction flow pump summary:

           Single stage double suction pump inlet flow, single-stage double suction centrifugal pump with two supports, is a British green company with single stage double suction pump design of the tenth edition of the API610, as the radial part of double support of high temperature hey load design, installation for the central support, the pump body is a double volute chamber; double suction impeller, citation of small good balance, axial; import and export are up, convenient installation and maintenance; sealing and flushing system according to the API682 standard design, all sealing and flushing plan to install the API682 code.

        This series of pumps is to meet the needs of large particles and conveying a harsh and hey work and special design, used in petroleum refining, petrochemical and chemical industries and other local transportation of petroleum and its products, it is fully in line with the American Petroleum Institute AP1610 specification.

        Imported single stage double suction flow pump has the characteristics of high reliability, long service life and high degree of generalization, especially high efficiency.

UK GRIMM Imported single stage double suction flow pump structure characteristics:

           The imported single stage double suction flow pump is a single stage double suction centrifugal pump with two ends supporting. The radial part of the pump shell. The utility model is especially suitable for conveying high temperature, high pressure, flammable and explosive or poisonous liquid, and the installation method is supported by a horizontal central line, so as to reduce the deformation and displacement caused by thermal expansion and cold contraction to a minimum. The pump body is designed with twin volute chambers to balance the radial forces of the pump.

         The pump can flow freely by the pressure liquid flow, but the upper part and the lower part of the volute are left with the umbilicus, and when the user needs to exhaust and drain the liquid, the ZG3/4 screw hole can be opened. At the work site plug screw.

         The suction and discharge flanges of the pump are vertically upward and are cast into the pump body. The flange sizes and pressure levels are equivalent to those adopted by the National Institute of standards (ANSI) standards. According to the service temperature and material category, the maximum flange pressure can reach 5MPa (about 50kgf/cm2).

In order to be reliable, the casting pump is made of cast steel shell, the hydrostatic pressure test is 7MPa (about 70kgf/cm2).

         The seal city (packing seal) and the pump cover are cast together, it can be packing seal and balance type, bellows or series of mechanical seal, water-cooled city outside the cast for the candidate's jacket, a water-cooling jacket must be equipped with special requirements or for water quality for water the temperature above 66 DEG C and hydrocarbon temperature exceeding 150 DEG C for the transmission medium. When the conveying medium needs to be insulated, low pressure steam or other heat insulating medium can be adopted in the jacket. Its hydrostatic pressure test 1MPa (about 10kgf/cm2) cooling water inlet connector ZG1/2; under the pump cover, outlet connector ZG1/2; above the pump cover.  Steam inlet joint ZG1/2 "; at the top of the cover; exit connector ZG1/2"; below the pump cover.

         Impeller as a whole casting parts, and with the rotor to do dynamic balance, it and the shaft is driven by a key, the rotor is supported at both ends. The sealing ring of the shell or the sealing ring of the impeller are all replaceable standard parts, and the good matching is ensured by the material and the different hardness. The sealing ring at both ends of the impeller design size of different sizes on the sealing ring is slightly less than the other side of the thrust bearing side of the pump, causing slight axial force, let shaft always in tension, oid the rotor moving around.

         Pump bearing body ends are the same size, material for steel and iron two, with screws on the bracket (tile frame), and with the stop position, by coupling is arranged at the end of a radial bearing, the other end is provided with two sets of back-to-back installed thrust ball bearings, bearings with oil ring lubrication oil. Moderate amount of each bearing in vitro cast heat sink for air cooling (T less than or equal to 120 DEG C), also can use cooling fan (T=120-260 C) and cooling water (T = 260 DEG C), which is particularly suitable for dry cooling fan or poor water quality in the region.

         When the pump bearings are cooled by fans, the fan will replace the position of the dust bowl, which is unique to the pump. When the pump bearings are cooled by water, the outside of the ball bearing is cast with a water-cooled jacket.

         The bearing body with transparent plastic circular oil and oil cup, to monitor and control the oil level, both ends of the bearing body is provided with a copper dust disc, the inner hole into the bearing cover, which can prevent dust or water from entering, and can prevent oil leakage. When the bearing is broken, it can still support.

         In order to repair without crack or unloading inhalation outlet pipe is easy to break out of the impeller, bearing, seal etc.. Single stage double suction pump using a flexible diaphragm type lengthened coupling parts, and the pump shaft are tapered with split packing is very convenient.

         Pump turn: turn counterclockwise from the prime mover to the pump.

UK GRIMM Imported single stage double suction flow pump technical Parameters:

Flow rate: 95-1740m3/h

Lift: 38-280m

Caliber: Inlet diameter: 150-400mm

             Outlet diameter: 100-300mm

Speed: 1480-2970r/min

Power: 75-710kw

Use temperature: -45 ~ +450 DEG C (special needs can reach -196 degrees Celsius)

Maximum working pressure: 5.0MPa

UK GRIMM Imported single stage double suction flow pump main use:

           Used in petroleum refining, petroleum, chemical and chemical industries and other places to transport petroleum.

进口单级双吸流程泵?官网:http://www.021fmc.cn/aspcms/product/2018-5-10/1328.html 

GRIMM中国:

    上海秉奇阀门有限公司GRIMM公司在中国的总代理,是中国拥有GRIMM代理权及销售权,主要为中国地区客户提供服务与技术支持,同时,秉奇人员也积极参与总部技术培训学习,并不断掌握产品原理、实际运作、工程技术做为基石,完善对中国地区客户需求。             

关于GRIMM

         英国格林(GRIMM)国际有限公司是亚太地区流体控制领域的主要生产和供应商之一,公司总部位于克莱福德,拥有一支有经验的研发队伍,实行全球统一设计,统一标准,在水泵领域内处于领先地位。在许多个国家均有生产水泵基地,中国由上海秉奇阀门负责中国市场各项业务与技术支持中心,同时向中国市场销售。

       英国格林(GRIMM)产品已广泛应用于市政给排水、建筑、石油、化工、液化气、食品、制药、发电、冶金、矿产、锅炉蒸汽系统、压力容器、原子能、航空、火箭等各领域,以及人们日常生活中。

       英国格林(GRIMM)主要产品有:管道泵、离心泵、隔膜泵、磁力泵、真空泵、潜水泵、排污泵、计量泵、卫生级泵、罗茨风机等系列产品。

服务体系:

GRIMM品质:

       GRIMM公司注重产品质量及使用寿命,全部采用先进制造技术和生产设备,并坚持不懈研发新产品,为确保不间断的全过程质量控制,在生产过程中采用(SPC)过程控制和(TQM)全面质量管理;GRIMM的严格规范实现了不让品质拖节,有效保障产品每个细节达到的性能指标。

GRIMM专业:

       掌握核心的流体控制技术,提供市场领先的产品、服务和解决方案,帮助用户提高效率,带来至关重要的基础设施。

GRIMM服务:

       我们与用户紧密合作,支持一系列系统使用技术和文件报告,提供售前、售中、售后服务和技术支持,有了您的信任与支持,我们将更完善、更高效提供水泵流体技术方案。

GRIMM china:

         Shanghai Bingqi Valve Co., Ltd. for GRIMM company general agent in China, is China with GRIMM proxy and sales rights, provide service and technical support, mainly for Chinese customers at the same time, will also actively participate in the training of technical personnel of butterfly learning headquarters, and continue to grasp the product principle, practical operation and Engineering Technology based on customer demand, improve the Chinese area.

About GRIMM:

         Uk GRIMM International Co., Lid is the field of fluid control in the Asia Pacific region is one of the main production and suppliers, the company headquarters is located in Clay Forde, has an experienced R & D team, the implementation of a global unified design, unified standards, a leading position in the field of water pump. In many countries, there are production pump base, China by the Shanghai Bingqi valve, responsible for the Chinese market business and technical support center, while selling to the Chinese market.

       Uk GRIMM products he been widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, metallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life.

       Uk GRIMM the main products are: pipeline pump, centrifugal pump, diaphragm pump, magnetic pump, vacuum pump, submersible pumps, sewage pumps, metering pumps, sanitary pump, blower and other products.

Service system:

GRIMM quality:

         GRIMM company pays attention to product quality and service life, all adopt the advanced manufacturing technology and production equipment, and unremittingly research and development of new products, the whole process of quality control to ensure uninterrupted, used in the production process (SPC) process control (TQM) and total quality management; strictly regulate the implementation of GRIMM has not let the quality drag day, effectively guarantee the performance of each product details.

GRIMM major:

          Fluid control technology master core, market leading products, services and solutions that help users improve efficiency, bring critical infrastructure.

GRIMM service:

          We work closely with the user, support a series of system using technology and file reports provide pre-sale, sale, customer service and technical support services, with your trust and support, we will be more perfect and more efficient to provide technical solutions of fluid pump.

英国格林总代理商:上海秉奇阀门有限公司,微信咨询:

Uk GRIMM total agents: Shanghai Bingqi Valve Co., Ltd., WeChat Advisory:

 

Welcome new and old customers call negotiate!

Contacts:Huang Tianxiang

QQ:673088832

Mobile Phone:13524269805 (微信同号)

Company Phone:021-51698378

Add:Lane 51, dragon road, Shanghai, Xuhui District


搜索更多:进口单级双吸流程泵

以下是上海秉奇泵阀有限公司信息发布人联系方式:

  • 免费企业会员
  • 上海秉奇泵阀有限公司
  • 进口隔膜泵,进口真空泵,进口潜污泵,进口计量泵,进口耐腐蚀泵
  • 黄天翔
  • 上海>>上海
  • 021-51698378
  • http://www.021fmc.cn
  • a51688@126.com
  • 2015-05-11
  • 上海市徐汇区龙漕路51弄
免责声明:

在本站发布的所有信息都由用户自行发布,信息中所表述的任何内容均与本站无任何关系,如果本站所展示的信息有侵犯到任何个人、企业或团体的权益,请与我们取得联系,并提供相应的证明文件,我们会尽最大努力保护您的权益。

置顶信息推广