用户名: 密码:  泵阀行业营销型网站建设
当前位置:网站首页 -> 水泵系列 >> 其他泵

进口潜水贯流泵(欧美进口十大品牌)发布时间:2018-08-02 09:38:48

进口潜水贯流泵

英国GRIMM格林进口潜水贯流泵 UK GRIMM Imported submersible pump


英国GRIMM格林进口潜水贯流泵概述:    

          进口潜水贯流泵是将潜水电机技术与贯流泵技术结合而产生的新型机电一体化产品,既保持了贯流泵本身的优点,又利用了潜水电机技术,又克服了传统贯流泵电机冷却、散热、密封等难题。

英国GRIMM格林进口潜水贯流泵特点:
该产品具有以下特点:
1、进、出水扬程损失小,泵站装置效率高。
2、相同工况下,电机功率配置小,运行费用较低。
3、水泵基础下无需设吸水槽,开挖量小。
4、泵管平直,适宜取消上部高大厂房,也可以不建厂房,用汽车吊装来取代固定式行车。
5、节省开挖量、本木工程费、建筑工程费,减少安装面积,节约泵站工程总造价30~40%。
6、安装快捷、安装方便。

英国GRIMM格林进口潜水贯流泵结构说明:

进口潜水贯流泵为卧式结构,从泵进口看,叶轮逆时针反向旋转。
1、叶轮:
     叶轮采用先进的水力模型换算所得,性能优良、稳定、成熟。选择较小的nD值,抗汽蚀性能好,确保运行平稳。
2、轴密封:
     较小的产品采用两套独立的机械密封,较大的产品采用层状剪切填料密封或机械密封以下不同的密封组合形式适应不同的结构,确保密封可靠,并可实现在线修复。
3、监测装置:
     进口潜水贯流泵装有多道保护装置,可把引线引至电控箱。保护装置有:过载、缺相、泄漏、超温、湿度、浸水等(视泵的结构不同而有差别)。
4、泵/电机轴:
     小型泵与电机同轴,结构紧凑,轴伸尽量缩短,并提高刚度,从设计上将挠度控制在允许范围内,运行时振动小,密封和轴承寿命更长;大型泵采用齿轮变速结构。
5、过水流道:
     采用CFD与实验方法相结合,确定流道流线形状,保证运行高效。
6、冷却:
     电机外壳直接将热量传到周围介质中并被周围的水流带走。大功率高电压电机,采用内风道散热专利技术,使得三相绕组温升低、温度场分布均匀。
7、电机:
     高性能鼠笼式感应电机,特别为潜水泵设计制造,符合GB755标准。绝缘等级F级,最高工作温度可达135℃。视功率不同,可采用380V、660V、3KV、6KV、10KV等电压等级,对高电压电机采用两次VPI绝缘工艺,确保绝缘可靠。
8、轴承:

     轴承采用滚动轴承,能够承受所有的轴向和径向负荷,并完全与泵输送的介质分开。

英国GRIMM格林进口潜水贯流泵技术参数: 
流       量:3213.8~36653m3/h
扬       程:1.6~10m
口       径:700~1600mm
转       速:290~740r/min
功       率:55~900kw
电       压:380V、660V、3KV、6KV、10KV
叶轮直径:600~1480mm

英国GRIMM格林进口潜水贯流泵主要用途: 
          进口潜水贯流泵适用于大流量、低扬程场合,主要用于雨水排放、工农业用水、区域调水、尤其适用于排涝与灌溉综合考虑的水利、防洪工程。如采用双向贯流泵,仅需改变电机的转向,即可实现正向抽水、反向排水。

英国GRIMM格林进口潜水贯流泵安装形式:

          进口潜水贯流泵一般采用干式安装(泵坑内无水、机组周围是干的,可以进行正常维护)。两端与管道采用伸缩节相连。其安装系统为预埋钢板,两只底脚螺栓、两只伸缩节。预埋钢板为一次性预埋件,预埋时必将混凝土中钢筋与钢板下部插筋焊接;底脚螺栓既可以一次预埋,也可以二次预埋;两端伸缩节为二次预埋件。
          安装时先将潜水贯流泵放到预埋钢板上,再依据其位置将连接螺栓与预埋钢板焊牢。如果底脚螺栓为一次预埋件,则以底脚螺栓作为定位依据;如果底脚螺栓要二次预埋,可在潜水泵就位后进行。然后依据设计图样,用楔铁调节贯流泵的高度,使其满足高程要求,最终将泵位置固定。泵运转时的轴向水推力由底脚螺栓和预埋钢板上的连接螺栓承受。
          接着将两只伸缩节与泵进出水端连接,确定伸缩节位置,再将混凝土外露钢筋与伸缩节焊接,最后进行二次灌浆。
          检修时如需要将泵吊起,先关闭检修门,将泵过水流道内的积水放掉,抽干泵坑,再将进出水两端的伸缩节松开,即可将泵吊离。安装时也只要反序进行。

UK GRIMM Imported submersible pump summary:

           New mechatronics products imported submersible axial-flow pump is combined with submersible motor technology and tubular pump technology and produce, while maintaining the advantages of tubular pump itself, and use of the submersible motor, but also overcomes the traditional tubular pump motor cooling, cooling, sealing and other problems.

UK GRIMM Imported submersible pump characteristic:

The product has the following characteristics:

1.The inlet and outlet water head loss is small, the pumping station device efficiency is high.

2.Under the same working conditions, the power allocation of the motor is small and the operation cost is low.

3.The pump foundation does not need to set suction trough, excation amount is small.

4.Pump tube straight, suitable for removal of the upper tall plant, can not build factories, cars to replace fixed crane hoisting.

5.Se the amount of excation, and the engineering costs, construction costs, reducing installation area, sing pumping station project total cost 30 ~ 40%.

6.Quick installation and easy installation.

UK GRIMM Imported submersible pump structure description:

Imported submersible tubular pump is horizontal structure, from the pump inlet, the impeller counterclockwise rotation.

1.Impeller:

   Impeller with advanced hydraulic model conversion, the performance of good, stable and mature. Select smaller nD value, good anti citation performance, ensure smooth operation.

2.Shaft seal:

   Smaller products using two independent sets of mechanical seal, the larger product adopts stratified shear packing seal or mechanical seal under different seal combination to adapt to different structure, to ensure reliable sealing, and can realize online repair.

3.Monitoring device:

   Imported submersible pump is equipped with multi-channel protection device, which can lead the lead to the electric control box. Protective devices are: overload, lack of phase, leakage, excessive temperature, humidity, flooding and so on (depending on the structure of the pump is different).

4.Pump / motor shaft:

   Small pump and motor shaft coaxial, compact structure, as short as possible, and improve the stiffness, deflection from design will be controlled within the allowable range, running small vibration, seal and bearing life longer; large pump adopts gear transmission structure.

5.Pass through the water channel:

   By using CFD and experiment method, the streamline shape of runner is determined, and the operation efficiency is guaranteed.

6.Cooling:

   The shell of the motor transfers heat directly to the surrounding medium and is taken away by the surrounding water. The high power and high voltage motor adopts the patented technology of inner duct heat dissipation, which makes the three-phase winding rise at low temperature and the temperature field is even.

7.Motor:

   High performance squirrel cage induction motors, designed especially for submersible pumps, comply with GB755 standards. The insulation grade is F, and the highest working temperature is 135 centigrade. Depending on the power, the 380V, 660V, 3KV, 6KV, 10KV and other voltage levels can be adopted. The two VPI insulation process is adopted to ensure the insulation reliability of the high voltage motors.

8.Bearings:

   The bearings are made of rolling bearings, capable of withstanding all axial and radial loads and are completely separated from the medium conveyed by the pump.

UK GRIMM Imported submersible pump technical Parameters:

Flow rate: 3213.8 ~ 36653m3/h

Lift: 1.6 ~ 10m

Caliber: 700 ~ 1600mm

Speed: 290 ~ 740r/min

Power: 55 ~ 900kw

Voltage: 380V, 660V, 3KV, 6KV, 10KV

Impeller diameter: 600 ~ 1480mm

UK GRIMM Imported submersible pump main use:

           Imported submersible pump is suitable for large flow and low lift occasions. It is mainly used for rainwater drainage, industrial and agricultural water use, regional water diversion, especially for water conservancy and flood control projects with comprehensive consideration of drainage and irrigation. If the bidirectional tubular pump is adopted, the positive pumping and reverse drainage can be realized only if the steering of the motor is changed.

UK GRIMM Imported submersible pump installation form:

            Imported submersible pumps generally use dry installation (pump pit without water, the unit is dry around, can be normal maintenance). The two ends are connected with the pipe by a telescopic joint. The installation system for pre embedded steel plate, two foot bolt and two telescopic joint. Embedded steel for one-time embedded parts, embedded in concrete and steel reinforced will lower inserted reinforcement welding; the foot bolt can be an embedded, can be two times the pre buried section; both ends of the telescopic two embedded parts.

         When you first install the submersible axial-flow pump into the pre buried steel plate, then on the basis of the position of the connecting bolt and embedded steel plate welding. If the foot bolt is a embedded in the foot bolt as a positioning reference; if the foot bolt two times embedded, can be carried out in the submersible pump in place. Then, according to the design drawing, the height of the tubular pump is adjusted by the wedge, so that it meets the requirement of elevation, and finally the pump position is fixed. Axial force of water pump running by the foot bolt and the pre buried steel plate connection bolts.

         Then, the two expansion joints are connected with the water inlet and outlet of the pump to determine the expansion joint position, then the exposed steel bar and the expansion joint are welded, and finally the two grouting is carried out.

         Overhaul, such as the need to pump the lift, first closed the door, the pump will flow off the water in the road release, drain the pump pit, and then enter the water at both ends of the expansion joint to loosen, you can pump the pump from. The installation also takes place only in reverse order.

进口潜水贯流泵?官网:http://www.021fmc.cn/aspcms/product/2018-5-10/1342.html 

GRIMM中国:

    上海秉奇阀门有限公司GRIMM公司在中国的总代理,是中国拥有GRIMM代理权及销售权,主要为中国地区客户提供服务与技术支持,同时,秉奇人员也积极参与总部技术培训学习,并不断掌握产品原理、实际运作、工程技术做为基石,完善对中国地区客户需求。             

关于GRIMM

         英国格林(GRIMM)国际有限公司是亚太地区流体控制领域的主要生产和供应商之一,公司总部位于克莱福德,拥有一支有经验的研发队伍,实行全球统一设计,统一标准,在水泵领域内处于领先地位。在许多个国家均有生产水泵基地,中国由上海秉奇阀门负责中国市场各项业务与技术支持中心,同时向中国市场销售。

       英国格林(GRIMM)产品已广泛应用于市政给排水、建筑、石油、化工、液化气、食品、制药、发电、冶金、矿产、锅炉蒸汽系统、压力容器、原子能、航空、火箭等各领域,以及人们日常生活中。

       英国格林(GRIMM)主要产品有:管道泵、离心泵、隔膜泵、磁力泵、真空泵、潜水泵、排污泵、计量泵、卫生级泵、罗茨风机等系列产品。

服务体系:

GRIMM品质:

       GRIMM公司注重产品质量及使用寿命,全部采用先进制造技术和生产设备,并坚持不懈研发新产品,为确保不间断的全过程质量控制,在生产过程中采用(SPC)过程控制和(TQM)全面质量管理;GRIMM的严格规范实现了不让品质拖节,有效保障产品每个细节达到的性能指标。

GRIMM专业:

       掌握核心的流体控制技术,提供市场领先的产品、服务和解决方案,帮助用户提高效率,带来至关重要的基础设施。

GRIMM服务:

       我们与用户紧密合作,支持一系列系统使用技术和文件报告,提供售前、售中、售后服务和技术支持,有了您的信任与支持,我们将更完善、更高效提供水泵流体技术方案。

GRIMM china:

         Shanghai Bingqi Valve Co., Ltd. for GRIMM company general agent in China, is China with GRIMM proxy and sales rights, provide service and technical support, mainly for Chinese customers at the same time, will also actively participate in the training of technical personnel of butterfly learning headquarters, and continue to grasp the product principle, practical operation and Engineering Technology based on customer demand, improve the Chinese area.

About GRIMM:

         Uk GRIMM International Co., Lid is the field of fluid control in the Asia Pacific region is one of the main production and suppliers, the company headquarters is located in Clay Forde, has an experienced R & D team, the implementation of a global unified design, unified standards, a leading position in the field of water pump. In many countries, there are production pump base, China by the Shanghai Bingqi valve, responsible for the Chinese market business and technical support center, while selling to the Chinese market.

       Uk GRIMM products he been widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, metallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life.

       Uk GRIMM the main products are: pipeline pump, centrifugal pump, diaphragm pump, magnetic pump, vacuum pump, submersible pumps, sewage pumps, metering pumps, sanitary pump, blower and other products.

Service system:

GRIMM quality:

         GRIMM company pays attention to product quality and service life, all adopt the advanced manufacturing technology and production equipment, and unremittingly research and development of new products, the whole process of quality control to ensure uninterrupted, used in the production process (SPC) process control (TQM) and total quality management; strictly regulate the implementation of GRIMM has not let the quality drag day, effectively guarantee the performance of each product details.

GRIMM major:

          Fluid control technology master core, market leading products, services and solutions that help users improve efficiency, bring critical infrastructure.

GRIMM service:

          We work closely with the user, support a series of system using technology and file reports provide pre-sale, sale, customer service and technical support services, with your trust and support, we will be more perfect and more efficient to provide technical solutions of fluid pump.

英国格林总代理商:上海秉奇阀门有限公司,微信咨询:

Uk GRIMM total agents: Shanghai Bingqi Valve Co., Ltd., WeChat Advisory:

 

Welcome new and old customers call negotiate!

Contacts:Huang Tianxiang

QQ:673088832

Mobile Phone:13524269805 (微信同号)

Company Phone:021-51698378

Add:Lane 51, dragon road, Shanghai, Xuhui District


搜索更多:进口潜水贯流泵

以下是上海秉奇泵阀有限公司信息发布人联系方式:

  • 免费企业会员
  • 上海秉奇泵阀有限公司
  • 进口隔膜泵,进口真空泵,进口潜污泵,进口计量泵,进口耐腐蚀泵
  • 黄天翔
  • 上海>>上海
  • 021-51698378
  • http://www.021fmc.cn
  • a51688@126.com
  • 2015-05-11
  • 上海市徐汇区龙漕路51弄
免责声明:

在本站发布的所有信息都由用户自行发布,信息中所表述的任何内容均与本站无任何关系,如果本站所展示的信息有侵犯到任何个人、企业或团体的权益,请与我们取得联系,并提供相应的证明文件,我们会尽最大努力保护您的权益。

置顶信息推广